Glue Products

Airsail Glues and Dopes

 

Airsail Balsa Cements: Well trusted New Zealand brand of liquid cement available in 50ml, 100ml and 200 ml sizes.

Airsail Aliphatic Wood Glue: Water proof, quick drying aliphatic wood glue available in 50ml, 100ml and 250 ml sizes.

 

Airsail Dopes:

  • Traditional dopes manufactured by Airsail used by modellers for years.
  • Weak Dope in 50ml, 100ml and 250 ml sizes.
  • Strong Dope in 50ml and 100ml ml sizes.
  • Non Shrink Dope in 50mland 250 ml sizes.
  • Sanding Sealer in 50ml and 100ml ml sizes.
  • Colour Dopes in 50 ml only

Cyanoacrylates


 

Cyanoacrylates (CAs) have become the adhesive of choice for most hobby and household applications. High quality CAs such as INSTA-CURE™, when used properly, form bonds that in many cases are stronger than the material that is being adhered. INSTA-CURE™ is a highly refined CA which, combined with its freshness, gives a guaranteed 2 year shelf life.

INSTA-CURE™ has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds.

INSTA-CURE+™ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds.

MAXI-CURE™ extra thick CA is the best CA for most plastics, including GE’s Lexan MAXI-CURE™ is the best choice for plastic model assembly. When used with INSTA-SET™, it works better than any putty for modifying or filling voids. It can be carved with a knife or razor blade and sanded and feathered to form a finish indistinguishable from plastic.

IC-2000™ is a rubber-toughened cyanoacrylate that forms superior shock resistant bonds on non-porous surfaces. The black colored CA has added flexibility for the bonding of metals, fiberglass, rubber, carbon-fiber and other advanced materials.

IC-GEL™ is a cyanoacrylate paste that is extremely thick which comes in an applicator tube like toothpaste. It has the same bonding and curing time characteristics as MAXI-CURE.

INSTA-FLEX™ flexible thin CA is ideal for many applications, including the installation of CA hinges. When cured, INSTA-FLEX™ does not turn brittle and remains clear, even if accelerated with INSTA-SET™.

INSTA-FLEX+™ clear rubber toughened has similar qualities to our black IC-2000™ but can be used in applications where you do not want the adhesive to be seen.

Odourless Cyanoacrylates

 

Odourless cyanoacrylates are formulated for use by those persons who have become sensitized or allergic to standard CA. Their use is recommended whenever sufficient ventilation is not possible. Odorless CAs have slightly less strength when compared to standard CA and are much more expensive. They can be used, however, on materials such as white foam that are otherwise dissolved or frosted by standard CA.

SUPER-GOLD™ and SUPER-GOLD+™ are our odorless INSTA-CURE CAs They are non-frosting and take only 2 or 3 seconds longer to bond. There are no fumes that irritate the nose and eyes. The SUPER-GOLD™’s do not attack white foam; therefore, they can be used in the building of foam core wings and the assembly and repair of plastic and foam ARF’s.

Accelerators

The surface properties of some materials, such as being acidic or having very low moisture content, slow down the curing of cyanoacrylates. CA accelerator is formulated to harden CA in ten seconds or less.
 

Threadlockers

BSI’s IC-Loc™ threadlockers are anaerobic adhesives that cure in the absence of air, which occurs as a threaded fastener is tightened. They prevent the loosening of fasteners due to shock or vibration. Full strength is reached in 1-3 hours.

IC-Loc™ Blue is a medium thickness, medium strength threadlock that is applied to the threads of fasteners before assembly. Once the IC-Loc Blue™ is cured, the fasteners can be disassembled with standard hand tools if required.
IC-Loc™ Red is a medium thickness, high strength threadlock that is applied to the threads of fasteners before assembly. Once the IC-Loc Red™ is cured, the fasteners are permanently together and cannot be disassembled. IC-Loc Red™ will maintain its strength up to 490º F.
IC-Loc™ Green is a thin, medium-high strength threadlock that is applied to fasteners that are already assembled. IC-Loc Green™ wicks down into the threads of fasteners using capillary action and has good performance even with oil coated fasteners.

Epoxies

 

QUIK-CURE™ 5 min. epoxy cures to a slightly flexible consistency. This lack of brittleness allows it to form a lasting bond in areas subjected to high vibration or stress. QUIK-CURE™ shouldn’t be used in areas that are subject to long-term immersion in water; however, it works fine for the internal structure of wood framed boats. QUIKCURE™ is our only epoxy on which you can apply polyester resins. It can be mixed with microballoons to form a quick setting putty. Items bonded with QUIK-CURE™ can be handled after 15 minutes. Full strength is reached in 1 hour.

MID-CURE™ 15 min. epoxy is used in larger areas where more working time is needed. It is more water resistant and can be used as a substitute for QUIK-CURE™ in most applications. MID-CURE™ is our most flexible epoxy and is ideal for gluing to fiberglass surfaces. Allow 45 minutes before handling parts and 2 hours for full strength.

SLOW-CURE™ 30 min. epoxy works best for forming reinforcing fillets on joints. It has the highest strength of our epoxies. It is waterproof and more heat resistant. SLOW-CURE™ can be used for bonding if you’re willing to wait overnight. Fillers such as microballoons can be mixed with SLOW-CURE™ and FINISH-CURE™ to form a putty-like consistency. Such fillers will usually decrease the working time by about 25%. Bonded objects can be handled after 8 hours and the cured epoxy reaches full strength within 24 hours.

FINISH-CURE™ 20 min. epoxy is an excellent, low odor substitute for polyester resins. It can be used for applying fiberglass cloth to wood or by itself to give wood a surface ready for primer and paint. FINISH-CURE™ can be sanded the easiest of all our epoxies and is excellent for the sheeting of foam core wings. Allow 8 hours for full curing.

Adhesive Selection Chart

If you are having trouble selecting the correct adhesive for your project, the chart below will help you.